GW Instek LCR-8000G Series User Manual Download Page 26

Page: 26 / 144

LCR-8000G Series User Manual

Tutorials (Step by Step Operations)

Basic measurement (without Pass/Fail test)

Step

Description

Details

1. Connect fixture

Connect the fixture to the DUT.

Page24

2. Enter menu

Press the Menu key, followed by F1 (AC
measurement) or F2 (Rdc).

Page48

3. Hide scale

Press F4 (Show/Hide Scale) to hide the
scale (or show the circuit diagram)

Page50

4. Select measur-
ement item

Press F1 (First) and F2 (Second)
repeatedly to select the measurement
item.

Page51

5. Select series/
parallel circuit

If available, press F3 (Series/Parallel) to
select the equivalent circuit model.

Page51

6. Set
measurement
frequency

Press the Left/Right arrow key and move
the cursor to the Frequency. Use the
numerical and unit keys to set the
frequency.

Page53

7. Set
measurement
Voltage

Press the Left/Right arrow key and move
the cursor to the Voltage. Use the
numerical and unit keys to set the level.

Page55

8a. Select Single
measurement

Press the Sing/Rep key to select Single
(manual trigger) measurement. To trigger
measurement, press the Trig key.

Page56

8b. Select
Repetitive
measurement

Press the Sing/Rep key to select
Repetitive (automatic trigger)
measurement. Press the Left/Right arrow
key and move the cursor to Speed. Press
the Up/Down key to select the speed.

Page57

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LCR-8000G Series

















































































































































Search results

Summary of Contents for LCR-8000G Series

Reviews:

Related manuals for LCR-8000G Series

Brands by name

Popular brands

GW Instek LCR-8000G Series, User Manual

Search results

Summary of Contents for LCR-8000G Series

Reviews:

Related manuals for LCR-8000G Series

Brands by name

Popular brands