GW Instek LCR-8000G Series User Manual Download Page 57 | Manualshive

Page: 57 / 144

background image

BASIC MEASUREMENT

57

Select Repetitive measurement

Background

The data capture can be manually controlled
(Single) or automatically updated (Repetitive).
In single measurement, the measurement is
activated by pressing the Trigger key.
In repetitive measurement, the measurement is
automatically done and the display is updated
according to the speed (timing) setting.

Panel operation

1.

Press the Sing/Rep key repeatedly
until the “Repetitive Mode” message
appears on the display.

Sing/Rep

Repetitive Mode

2.

The measurement update indicator (*) keeps
blinking and the measurement result is updated
on the display.

MEASUREMENT MODE

0.01234

0.2179

nS

D

*7

–

3.

Press the Left/Right key repeatedly
to move the cursor to measurement
speed.

Speed Slow

4.

Press the Up/Down key repeatedly
to select the time per update.

www.

.com

[email protected]

1.800.561.8187

«
...
55
56
57
58
59
...
»

Summary of Contents for LCR-8000G Series

















































































































































Reviews:

No comments

Related manuals for LCR-8000G Series

Brand: Kawai Pages: 2

Brand: E Instruments Pages: 2

Brand: Gardner Bender Pages: 7

Brand: NanoEnTek Pages: 4

Brand: Unior Pages: 2

Brand: Vaisala Pages: 83

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: Omega Pages: 24

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brand: Bontempi Pages: 18

Brand: H. HERMANN EHLERS Pages: 40

Brand: Osaka Pages: 3

Brand: SIKA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands