Gree GMV-1015WM/H-X Owner'S Manual Download Page 51

Page: 51 / 77

GMV DC Inverter VRF

NOTE!

The maximum connection number “N” of outdoor unit and the maximum connection number “n”

of indoor unit are decided by the combination method of outdoor unit. For details, please refer to the

part of unit capacity configuration.

3.8.4 Wiring Diagram

Refer to the wiring diagram attached on the unit.

3.9 Communication Line Connection

Adopt CAN bus communication mode between indoor unit and outdoor unit as well among indoor

units.

3.9.1 Connection Method of Communication Line Terminal

Communication connections adopts screws for fixing.

Fig. 3.9.1

3.9.2 Communication Material Selection

NOTE!

If the air conditioning unit is installed in a place with strong electromagnetic interference, the

communication line between the indoor unit and the wired controller must adopts shielded wires; the

communication line between indoor units (between indoor unit and outdoor unit) must use the

shielded twisted pairs.

(1) Selection of communication line between indoor unit and wired controller.

Wire type

Length of

communication

line between

indoor unit and

wired controller(m)

Wire diameter

(mm

)

Wire standard

Remark

Light / ordinary PVC

sheathed twisted copper

core cord

≤250

2×0.75~2×1.25 IEC 60227-5:2007

The length of

communication line can't

exceed 250m.

Shielded light/ordinary PVC

sheathed twisted copper

core cord

≤250

2×0.75~2×1.25 IEC 60227-5:2007

When the installation

environment of the unit is in

strong magnetic or strong

interference, the shielded

wires shall be used.

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands