Gree GMV-1015WM/H-X Owner'S Manual Download Page 69

Page: 69 / 77

GMV DC Inverter VRF

Debugging Parameter Reference Value for DC Inverter VRF Unit

No.

Debugging item

Parameter name

Unit

Reference value

Remark

System

parameter

Outdoor

unit's

parameter

Drive bus voltage of
inverter compressor

●

The normal bus voltage is 1.414 times of the

power supply voltage. For example, if the
three-phase power supply voltage is 390V, then
the rectified bus voltage is: 390V

1.414 =

551V. The normal deviation between the
measured value and the calculated value within
15V.

——

Fan operation

frequency

●

Adjust the operation in the range of 0~90Hz

according to the system pressure adjustment.

——

Indoor

unit's

parameter

Inlet tube temperature

of indoor heat

exchanger

℃

●

According to the ambient temperature, the

inlet temperature is 1

℃

lower than the

outlet temperature for the same indoor unit
under cooling mode.

●

The inlet temperature is 1

℃

lower than

the outlet temperature for the same indoor unit
under the heating mode.

——

Outlet tube temperature

of indoor heat

exchanger

℃

——

Opening of indoor

electronic expansion

valve

PLS

●

2000PLS electronic expansion valve: the

opening is adjusted automatically in the range of
200~2000PLS;

●

480PLS electronic expansion valve: the

opening is adjusted automatically in the range of
70~480PLS.

——

Drainage

system

——

—

●

The indoor unit drains smoothly and

thoroughly, and the condensate water pipe has
no slope water storage; the outdoor unit can
drain water from the drain pipe without dripping
directly from the unit foundation.

——

Other

——

—

●

There is no abnormal noise for the operation

of the compressor, indoor fan and outdoor fan.
The unit is running normally.

——

5 Operation Instruction

For instructions on how to use the air conditioner, please refer to the user manual of wired

controller or remote controller.

6 Maintenance

Regular inspection and maintenance can extend the service life of the air conditioning unit.

6.1 Heat Exchanger of Outdoor Unit

The heat exchanger of outdoor unit should be cleaned regularly. A vacuum cleaner can be used

with a nylon brush to clean dust and debris from the surface of the heat exchanger. If there is

compressed air source, the compressed air can be used to blow dust from the surface of the heat

exchanger. Do not wash it with tap water.

6.2 Drain Pipe

The drain pipe should be checked regularly to allow the condensate to drain smoothly.

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands