Gree GMV-1015WM/H-X Owner'S Manual Download Page 18

Page: 18 / 77

GMV DC Inverter VRF

No.

Name

Pipe diameter

GMV-400WM/H-X

GMV-450WM/H-X

①

Gas pipe

25.4

28.6

②

Liquid pipe

12.7

③

Pipe and wiring passing hole

(LxW)

234×69

④

Hoist hole

No.

Name

Pipe diameter

GMV-504WM/H-X

GMV-560WM/H-X

GMV-615WM/H-X

①

Gas pipe

28.6

②

Liquid pipe

15.9

③

Pipe and wiring passing hole

(LxW)

234×69

④

Hoist hole

3.2.2 Select Installation Position

Conditions for selecting the installation position:

(1) Install the unit at a place where is adequate to withstand the weight of the unit and make

sure the unit would not shake or fall off.

(2) Fully consider the influence of strong winds, typhoons and earthquakes when selecting the

installation site, and strengthen the installation.

(3) The influence of flammable, explosive, corrosive gases or exhaust gases should be avoided.

(4) Ensure that there is a certain space for heat exchanging and maintenance, so that the

ventilation is smooth and the running is reliable.

(5) Outdoor units and indoor units should be as close as possible to minimize the length and

angle of the cooling pipes.

(6) Do not allow children to approach the unit. Preventive measures should be taken to prevent

children from contacting the unit.

(7) The unit should not be installed in places with high environmental pH or high voltage

fluctuations, and places such as vehicles and ships.

(8) Do not install the unit at the place where is close to the equipment that generates

electromagnetic waves. Electromagnetic waves can affect the control system and cause

fault.

3.2.2.1 Take Seasonal Wind into Consideration When Installing the Outdoor Unit

(1) Anti-monsoon installation requirements for unit not connecting exhaust duct.

When the exhaust duct is not connected, a protective cover should be installed according to the

seasonal wind circumstances.

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands