Gree GMV-1015WM/H-X Owner'S Manual Download Page 37

Page: 37 / 77

GMV DC Inverter VRF

(3) According to the size of the unit and steel plate ventilation pipe, prepare suitable canvas

casing, tin foil paper, steel strip and self-tapping screws, and prepare tools such as electric

drill, screwdriver, etc.

3.5.2 Ventilation Pipe Installation

When the effective area of the air inlet is less than 70% of the total inlet area of all outdoor unit, it

needs to add an induced draft fan. The total air volume of the induced draft fan is not less than 80% of

the total intake air volume.

NOTE!

In the following table, “1” indicates the steel plate ventilation pipe, “2” indicates the outdoor unit,

“3”indicates the top cover assembly, “4” indicates the canvas casing and “5” indicates the steel bar.

The specific operations are as below:

Step

Photo

Operation instruction

Note

Step 1

①

Select installation

position for the outdoor
unit and then fix it well;

②

Determine the

installation position of
the ventilation pipe
according to the
position of the outdoor
unit;

③

Refer to the left figure

to complete the
fabrication and
installation of the
ventilation pipe.

①

Ventilation pipe

material: steel plate
or iron sheet;

②

Ventilation pipe

should be purchased
by the user.

Step 2

①

Remove the

self-tapping screws
around the top cover
assembly with
screwdriver and then
remove the top cover
assembly.

②

Remove the grille on

the top of the top cover
assembly.

The top cover grille
must be removed;
otherwise it will affect
the air volume and the
operation effect.

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands