Gree GMV-1015WM/H-X Owner'S Manual Download Page 70

Page: 70 / 77

GMV DC Inverter VRF

6.3 Precautions at the Beginning of Using Season

(1) Check whether all air inlet and air outlet of indoor unit and outdoor unit are not blocked.

(2) Check if the grounding is reliable.

(3) Check if the battery of the remote controller has been replaced.

(4) Check if the air filter is properly installed.

(5) When restart up the unit after it has been stop operation for a long time, turn on the air

conditioner's power switch 2 hours before starting the operation to preheat the outdoor

compressor crankcase.

(6) Check if the outdoor unit is installed firmly. If there is any abnormality, please contact Gree

service center.

6.4 Maintenance at the End of Using Season

(1) Cut off the main power of the air conditioning unit.

(2) Clean the filter and indoor and outdoor units' body.

(3) Remove dust and debris from indoor and outdoor units.

(4) If the outdoor unit is rusted, smear the oil paint to prevent it from expansion.

6.5 Parts Replacement

Accessories are available through the nearby GREE office or GREE dealer.

NOTE!

Do not mix dangerous gases such as oxygen and acetylene into the refrigeration circuit during air

tightness and leak test! To avoid danger, it is best to use nitrogen for such tests.

7 Troubleshooting

7.1 Common Malfunction and Troubleshooting

Check the following items before asking for repair.

Phenomenon

Reason

Measure

The unit doesn't run.

Without power supply

Connect to power supply

Voltage is too low

Check if the voltage is within rating range

Broken fuse or breaker trips off

Replace fuse or connect breaker

Insufficient energy of remote controller

Replace new battery

Remote controller is out of control
scope

Control scope is within 8m

Unit runs but stop

immediately

Air intake or outlet of indoor or outdoor
unit is blocked

Remove obstruction

Abnormal cooling or

heating

Air intake or outlet of indoor or outdoor
unit is blocked

Remove obstruction

Improper temperature setting

Adjust setting at wireless remote controller or
wired controller

Fan speed is set too low

Adjust setting at wireless remote controller or
wired controller

Wind direction is not correct

Adjust setting at wireless remote controller or
wired controller

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands