Gree GMV-1015WM/H-X Owner'S Manual Download Page 72

Page: 72 / 77

GMV DC Inverter VRF

7.2 Error Indication

NOTE!

For specific unit fault and maintenance, please refer to the engineering debugging and

after-sales maintenance manual of DC inverter VRF unit.

——

Error

Code

Content

Error

Code

Content

Indoor

Malfunction of IDU

Protection of indoor fan

Auxiliary heating protection

Water-full protection

Abnormal power supply for wired
controller

Freeze prevention protection

Mode conflict

No main IDU

Power supply is insufficient

For single control over multiple units, number
of IDU is inconsistent (HBS network)

For single control over multiple units, IDU
series is inconsistent (HBS network)

Alarm due to bad air quality

IDU is not matching with outdoor unit

Malfunction of water flow switch

Rotation speed of EC DC water pump is
abnormal

Malfunction of shunt valve setting

Setting of functional DIP switch code is
wrong

Zero-crossing malfunction of PG motor

For single control over multiple units, IDU is
inconsistent (reheating-dehumidifying
system)

Indoor PCB is poor

Malfunction of lower water temperature
sensor of water tank

Malfunction of ambient temperature
sensor

Malfunction of entry-tube temperature sensor

Malfunction of mid-tube temperature
sensor

Malfunction of exit-tube temperature sensor

Malfunction of humidity sensor

Malfunction of water temperature sensor

Malfunction of jumper cap

Web address of IDU is abnormal

PCB of wired controller is abnormal

Setting capacity of DIP switch code is
abnormal

Malfunction of air outlet temperature
sensor

Malfunction of indoor CO

sensor

Malfunction of upper water temperature
sensor of water tank

Malfunction of backwater temperature sensor

Malfunction of inlet tube temperature
sensor of generator

Malfunction of drainage pipe temperature
sensor of generator

Debugging status

Malfunction of solar power temperature
sensor

Malfunction of swing parts

Malfunction of water temperature sensor

Malfunction of entry-tube temperature
sensor 2

Malfunction of exit-tube temperature sensor
2

Malfunction of fresh air inlet temperature
sensor

Malfunction of IDU's air box sensor

Malfunction of IFD

Low-voltage protection of IDU's bus bar

High-voltage protection of IDU's bus bar

IPM module protection of IDU

Failure startup of IDU

Over-current protection of IDU

Malfunction of current detection circuit of
IDU

Desynchronizing protection of IDU

Communication malfunction of IDU's
driver

Communication malfunction of IDU's main
control

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands