Gree GMV-1015WM/H-X Owner'S Manual Download Page 12

Page: 12 / 77

GMV DC Inverter VRF

2.4 Product Working Principle

2.4.1 Working Principle Introduction

The outdoor unit of GMV6 multi VRF unit can be realized by parallel combination of modules, and

the indoor unit can also be composed of multiple units in parallel. The working principle is as follows:

when the indoor unit is running in the cooling mode, the outdoor unit starts the outdoor module

according to the running load demand of the indoor unit. The outdoor heat exchanger is used as the

condenser of the system, and the heat exchangers of indoor units are connected in parallel as the

evaporator of system. It realizes the adjustment of the air temperature and humidity for indoor space

through the return air circulation of the indoor unit; when the indoor unit is in the heating mode, all the

four-way valves of the outdoor unit module are switched to the energizing state, the outdoor heat

exchanger is used as the evaporator of the system and the heat exchanger of indoor unit is used as

the condenser of the system. The air temperature and humidity in the indoor space is realized by the

return air circulation of the indoor unit.

2.4.2 Working principle Diagram

System principle diagram of GMV-224WM/H-X , GMV-280WM/H-X , GMV-335WM/H-X

Fig. 2.4.1

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands