Gree GMV-1015WM/H-X Owner'S Manual Download Page 52

Page: 52 / 77

GMV DC Inverter VRF

The connection between the indoor unit and the wired controller is shown as below:

Fig. 3.9.2

(2) Selection of communication line between outdoor unit and indoor unit.

Wire type

Length of

communication

line between

indoor unit and

wired controller(m)

Wire diameter

(mm

)

Wire standard

Remark

Light / ordinary PVC

sheathed twisted copper

core cord

≤

1000

≥

0.75

IEC 60227-5:2007

If the wire diameter is

increased to 2

1mm

, the

length of communication line

can't be increased, while the

length of the communication

line can't be more than

1500m.

Shielded light/ordinary PVC

sheathed twisted copper

core cord

≤

1000

≥

0.75

IEC 60227-5:2007

When the installation

environment of the unit is in

strong magnetic or strong

interference, the shielded

wires shall be used.

Fig. 3.9.3

3.9.3 Communication Line Connection

Communication bus connection between indoor unit and outdoor unit must be connected in

series, rather than star connection; the endmost indoor unit of communication bus between indoor

unit and outdoor unit must connect with the communication matching resistor(in the outdoor unit

plastic bag); the fresh air indoor unit is not recommended to be set as the main indoor unit.

Summary of Contents for GMV-1015WM/H-X














































































Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands

Gree GMV-1015WM/H-X, Owner'S Manual

Search results

Summary of Contents for GMV-1015WM/H-X

Reviews:

Related manuals for GMV-1015WM/H-X

Brands by name

Popular brands