GRAUPNER MC-22S, Programming Manual

Page: 47 / 180

47
Model select
Model select 1 … 30
Copy / Erase
Model copy and fl ight phase copy function
0 1 C U M U L U S 9 7 S P C M 2 0 1 : 2 5 h
0 2 L a s e r P C M 2 0 2 : 4 5 h
0 3 D V 2 0 K A T A N A P P M 1 8 5 : 2 6 h
0 4 M E G A S T A R S P C M 2 0 8 : 3 1 h
0 5
V V V
f r e e
V V V
0 6
V V V
f r e e
V V V
The transmitter can store up to thirty complete sets
of model settings, including the digital trim values set
by the four trim levers. The trims are automatically
stored, which means that the settings you have care-
fully established through test-fl ying are not lost when
you swap models.
If you have entered a model name in the » Base se-
tup model « menu (page 50), the name appears af-
ter the model number, together with the model type
in pictogram form, the type of modulation and the
model’s operating time.
Use the rotary control to select from the list the model
you wish to use. Confi rm your selection by pressing
the rotary control, or press
ENTER . Pressing ESC
takes you back without switching models.
Notes:
• If the warning message “Throttle too high” appears
when you switch models, the throttle stick “Ch1” is
set towards full throttle, and should be returned to
idle.
• If the message “Fail-Safe setup” appears when you
switch models, you should check your Fail-Safe
settings. This only applies if the transmitter is set to
PCM20 or SPCM20 transmission mode.
• If the battery voltage is too low, it may not be pos-
sible to switch model memories for safety reasons.
In this case the screen displays this message:
E r a s e m o d e l = >
C o p y m o d e l ® m o d e l = >
C o p y M C 2 2 ® e x t e r n a l = >
C o p y e x t e r n a l ® M C 2 2 = >
C o p y f l i g h t p h a s e = >
S e c u r e a l l m o d e l s ® P C = >
t
s
This menu is used to:
• erase a model memory;
• copy internally from one model memory to ano-
ther;
• copy a model memory from one mc-22s transmit-
ter to another, from the mc-22s to the mc-22 or
mx-22, and from the mc-22s to an industry-stan-
dard PC;
• copy individual fl ight phases within one and the
same model memory.
• back up the data contained in all the model memo-
ries to a compatible PC.
To connect the transmitter to a PC you will need the
PC interface mc-22(s) / PC set, Order No.
4182 . This
is an optional accessory which is connected to the
interface distributor (supplied in the set), in order to
transfer model data to the PC, to back up the data on
diskette or hard disc, and – if necessary – to load it
back into the transmitter (or another transmitter). Full
details are included in the set (the PC interface lead
and interface distributor are also available separate-
ly; see Appendix). To transfer data between two mc-
22s transmitters, both transmitters must be fi tted with
the mc-22(s) interface distributor, Order No.
4182.3 .
You will also need the copy lead, Order No. 4179.2 , to
make the actual transfer.
Caution – essential information:
Be sure to connect the PC or the second transmitter to your mc-22s using the interface or copy lead be-
fore you switch the mc-22s transmitter on. When the process is completed, switch the transmitter(s) off
before you disconnect the lead!
Program description: Model memories
Copy lead
Order No. 4179.2
mc-22(s) mc-22(s) or mx-22
mc-22(s) mx-22
OR
PC interface lead
Order No. 4182.9
(see notes on page 163/164)
Not currently possible
Battery voltage too low