background image

Advanced Programming 

32

3A8848A

Entering a PIN Code for the First Time

A1-Setting Up PIN Code 

A PIN Code can be programmed into the G5 to protect 

the settings from inadvertently being changed by unau

-

thorized users. 

1. Press the UP ARROW button for 10 

seconds.

The LED next to the LOCK ICON on the 

display lights, indicating that the PIN Mode 

has been entered.

2. The word OFF appears in the 

display. Press the UP or 

DOWN ARROW button to 

change this to ON.

3. Press the ENTER button to enter the 

PIN Code.

4. The cursor automatically is 

positioned to entered the first 

character of the PIN Code. 

Use the UP and DOWN 

ARROW buttons to move up 

and down through the numbers 0-9 until the first 

number in the PIN code is displayed in the field. 

5. Press the ENTER button to set the 

number. The cursor automatically 

moves to the next number field.

6. Repeat steps and for each PIN Code prompt 

field.

7. Press the ENTER button to save the 

PIN Code and exit Advanced Setup.

Entering Advanced Setup

Press the UP ARROW button for 10 sec

-

onds.

If the G5 was previously set up to require a PIN Code, 

the LED next to the LOCK ICON lights, indicating a PIN 

Code is required. 

1. The cursor is automatically 

positioned to enter the first 

character of the PIN Code. 

Use the UP and DOWN 

ARROW buttons to move up 

and down through the numbers 0-9 until the first 

number in the PIN code is displayed in the field. 

2. Press the ENTER button to set the 

number. The cursor automatically 

moves to the next number field. 

3. Repeat steps and 2 for each PIN Code prompt 

field.

If the PIN Code entered is correct, the first editable 

character on the display will flash. 

Selecting Advanced Setup Options

1. Press the UP or DOWN 

ARROW button to move up 

or down through Advanced 

Options A1 and A2.

2. Press the ENTER button to set the 

selection.

A2 - Low Level Alarm Time

Pump ON mode only.

Programs the amount of time in MM: SS (minutes and 

seconds) the pump can run between a Low Level Warn

-

ing and a Low Level Fault to help protect unit from run

-

ning dry.

The maximum recommended length of time is 3:00 

minutes.

Summary of Contents for 95G104



















































Reviews: