Gorilla Playsets Savannah II 1500FT Manual Download Page 116

Page: 116 / 123

6) REPEAT 4 & 5 FOR REMAINING ROPE LADDER RUNGS.

10 58

THIS IS THE VIEW AS IF YOU WERE STANDING AT THE FRONT - RIGHT OF THE PLAY SET

5) SLIDE THE NEXT ROPE LADDER RUNG UP TO THE

MARKS OR TAPE. TIE THREE KNOTS UNDER THE ROPE

LADDER RUNG.

2) MEASURE DOWN 6" BELOW THE BOTTOM OF THE ROPE

LADDER SUPPORT AND TIE 3 KNOTS. THE BOTTOM OF EACH

KNOT SHOULD BE 6" BELOW THE ROPE LADDER SUPPORT.

7) TIE KNOTS ON BACK SIDE OF ROPE LADDER RUNNER.

2.1) SLIDE A ROPE LADDER RUNG AGAINST THE THREE KNOTS.

4) MEASURE DOWN 10-5/8" BELOW THE

ROPE LADDER RUNG AND PLACE TAPE ON

THE ROPE OR MARK WITH A PEN.

1) TIE A KNOT IN EACH ROPE AND THREAD THEM

THROUGH THE BACK SIDE OF THE ROPE LADDER SUPPORT.

ROPE LADDER SUPPORT

3) TIE THESE THREE KNOTS BELOW THE ROPE LADDER RUNG.

ROPE LADDER RUNNER

1: FIND THREE ROPE LADDER ROPES. MAKE A KNOT IN THE END OF EACH ROPE AND THREAD THE FREE END THROUGH THE BACK

SIDE OF THE ROPE LADDER SUPPORT. PULL EACH ROPE TAUGHT.

2: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER SUPPORT 6 INCHES AND TIE A KNOT. THE BOTTOM OF THE KNOT

SHOULD BE 6 INCHES BELOW THE ROPE LADDER SUPPORT. SLIDE EACH ROPE THROUGH THE HOLES IN ONE ROPE LADDER RUNG.

SLIDE THE RUNG UP AGAINST THE BOTTOM OF THE KNOTS.

3: TIE THREE KNOTS BELOW THE ROPE LADDER RUNG.

4: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER RUNG 10-5/8 INCHES AND MAKE A MARK ON THE ROPE WITH

APIECE OF TAPE OR A MARKER. THREAD ANOTHER ROPE LADDER RUNG ONTO THE ROPES.

5: WITH THE TOP OF THE RUNG EVEN WITH THE 10-5/8" MARK TIE THREE KNOTS BELOW THE SECOND ROPE LADDER RUNG.

6: REPEAT SUBSTEPS 4-5 FOR THE REMAINING ROPE LADDER RUNGS.

7: THREAD THE BOTTOM END OF EACH ROPE THROUGH THE HOLES IN THE ROPE LADDER RUNNER AND TIE THEM OFF.

GRAB EACH ROPE AND ATTEMPT TO WRAP IT AROUND YOUR HAND. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO

LOOSE. IF THE ROPE IS TOO LOOSE UNTIE THE KNOT BEHIND THE ROPE LADDER RUNNER AND RETIE IT UNTIL YOU CAN NO LONGER

WRAP THE ROPE AROUND YOUR HAND.

STEP 26: ROPE LADDER

108

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands