Gorilla Playsets Savannah II 1500FT Manual Download Page 53

Page: 53 / 123

16 "

CORNER POSTS AND ATTACH IT WITH 2" WOOD SCREWS THROUGH THE PREDRILLED HOLES AND INTO THE DECK

SUPPORT BELOW. NOTE THE TOP OF THE SCREW HEAD SHOULD BE FLUSH TO THE TOP OF THE DECK SPACER.

2: PLACE THE 5/4 X 4 X 40-3/8" DECK SPACER AT ONE END OF THE FORT. CENTER THE BOARD BETWEEN THE

2" WOOD SCREW

5/4 X 4 X 40-3/8"

DECK SPACER

FRONT OF FORT

NOTE: 2 X 4 X 47-1/2" END PANEL BOARDS REMOVED FOR CLARITY.

STEP 9: DECK SPACERS

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD

1: PRE-DRILL THE ENDS OF THE 5/4 X 4 X 40-3/8" DECK SPACERS TO PREVENT INSTALLATION DAMAGE.

PRE-DRILL BOTH ENDS WITH A1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW. THE HOLE AT 20-3/16" IS THE

CENTER OF THE BOARD AND ONLY NEEDS TO BE DRILLED ONCE. THIS HOLE IS TO ATTACH THE CENTER DECK

SUPPORT TO THE DECK SPACER.

BOARD. THIS HOLE ONLY

NEEDS TO BE DRILLED ONCE.

THIS IS THE CENTER OF THE

5/4 X 4 X 40-3/8"

DECK SPACER

3 "

11 "

8 "

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands