Gorilla Playsets Savannah II 1500FT Manual Download Page 62

Page: 62 / 123

STEP 18: ANGLE SUPPORTS

1: ONE 2 X 4 X 18" ANGLE SUPPORT IS MOUNTED UNDER THE DECK ON THE LEFT REAR OF THE PLAY SET. THE TOP OF

THE ANGLE SUPPORT SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

2: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE DECK SUPPORT INTO THE ANGLE SUPPORT. AT THE

BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE SUPPORT TO THE CORNER POST.

3: ONE 2 X 4 X 18" ANGLE SUPPORT IS MOUNTED UNDER THE DECK ON THE LEFT SIDE AT THE REAR OF THE PLAY SET

TO THE 2 X 6 X 47-1/2" PANEL BOARD CLATTER BRIDGE. THE TOP OF THE ANGLE SUPPORT SHOULD BE FLUSH OR

LOWER THAN THE TOP OF THE DECK SUPPORT.

4: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE ANGLE SUPPORT INTO THE 2 X 6 X 47-1/2" PANEL BOARD

CLATTER BRIDGE. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE SUPPORT TO THE

CORNER POST.

18"

SUPPORT

DECK SUPPORT

ANGLE

2 X 4 X 18"

ANGLE

CLATTER BRiDGE

SUPPORT

PANEL BOARD

2 X 6 X 47-1/2"

SHOULD BE FLUSH OR LOWER

DETAIL A

THAN THE DECK SUPPORT

TOP OF ANGLE SUPPORTS

HOLE FOR

THE CLATTER

BRIDGE

CHAIN

3" WOOD

SCREW

2-1/2"" WOOD

ANGLE

SCREW

2 X 4 X 18"

SCREW

DECK SUPPORT

2-1/2" WOOD

SCREW

3" WOOD

SCREW

2" WOOD

SCREW

2" WOOD

SUPPORT

2 X 4 X 18"

ANGLE

SUPPORT

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands