Gorilla Playsets Savannah II 1500FT Manual Download Page 109

Page: 109 / 123

CHAIN MUST GO THROUGH

TWO BOARDS NO EXCEPTIONS!!

1" TO 1-3/4"

LINK TO ATTACH THE CHAINS TOGETHER. IF YOU HAVE LOOSE ENDS OF THE CHAINS HANGING DOWN

THREAD THEM THROUGH THE QUICK LINK TO KEEP THEM UP AND OUT OF THE WAY.

PANEL BOARD ON THE TOWER. THIS MEANS THAT YOU WILL HAVE TO CONNECT THE ENDS OF THE CHAINS

2: THERE SHOULD BE AT LEAST A 1" TO 1-3/4" GAP BETWEEN THE BRIDGE DECK BOARD AND THE BOTTOM

IN A MANNER TO ACHIEVE THE CORRECT GAP. GO UNDERNEATH THE TOWER DECK AND USE A QUICK

STEP 19: BRIDGE DECK/CHAIN INSTALLATION

1: LAY THE BRIDGE DECK/CHAINS ASSEMBLY BETWEEN THE PLAY SET AND THE TOWER WITH THE CHAINS

FACING THE GROUND. THREAD THE CHAIN ENDS IN THE BRIDGE DECK ASSEMBLY THROUGH THE HOLES IN

THE BOTTOM PANEL BOARD AND DECK SUPPORT BOARD ON THE TOWER.

3: REPEAT THIS PROCESS AT THE PLAY SET

TO ATTACH THE CHAINS. AT THE PLAY SET EACH

CHAIN MUST GO THROUGH TWO BOARDS.

NO EXCEPTIONS.

QUICK LINK

DETAIL A

SCALE 1 : 6

NOTE: TO ACHIEVE THE CORRECT

GAP YOU MAY NOT BE CONNECTING

THE END LINK OF EACH CHAIN. FOR

EXAMPLE YOU MAY HAVE TO

CONNECT THE SECOND, THIRD OR

FOURTH LINKS TOGETHER.

101

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands