Gorilla Playsets Savannah II 1500FT Manual Download Page 92

Page: 92 / 123

SANDBOX BOARD

(OFFSET UP)

HEX BOLT

FRONT OF TOWER

2 X 4 X 36-3/4"

TOP PANEL BOARD

5/16" WASHER

2 X 6 X 36-3/4"

5/16 X 4-1/2"

T-NUT ON OUTSIDE

RIGHT SIDE

NO T-NUTS

IN THESE

HOLES

T-NUT ON OUTSIDE

STEP 2: ASSEMBLING THE RIGHT SIDE FRAME

5: DO NOT INSTALL LAG SCREWS AT THIS TIME.

1: LAY THE 2 X 6 X 36-3/4" SANDBOX BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS AT THE BOTTOM OF THE

CORNER POSTS. THE COUNTERSUNK HOLES IN THE SANDBOX BOARD MUST BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: LAY THE 2 X 4 X 36-3/4" TOP PANEL BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE COUNTERSUNK HOLES OF THE TOP PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS.

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands