Gorilla Playsets Savannah II 1500FT Manual Download Page 47

Page: 47 / 123

STEP 3: ASSEMBLING THE RIGHT SIDE FRAME

FRONT OF FORT

1: LAY THE RIGHT SIDE CORNER POSTS ON THE GROUND IN THEIR PROPER ORIENTATION.

2: LAY THE 2 X 6 X 47-1/2" SANDBOX BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS AT THE BOTTOM OF THE

CORNER POSTS. THE HOLES IN THE SANDBOX BOARD MUST BE OFFSET DOWN.

3: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

4: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE LEFT SIDE CORNER POSTS IN THE MIDDLE OF THE

CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.

5: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.

6: LAY THE 4 X 4 X 47-1/2" SWING BEAM MOUNT ON TOP OF THE RIGHT SIDE CORNER POSTS. THE THREE

COUNTERSUNK HOLES IN THE MIDDLE OF THE SWING BEAM MOUNT MUST FACE DOWNWARD.

7: FIND TWO TORQUE WASHERS. PLACE A 6-1/2" CARRIAGE BOLT THROUGH THE TORQUE WASHER, MAKING SURE

THAT THE TEETH ARE FACING IN THE SAME DIRECTION AS THE THREADS OF THE CARRIAGE BOLT. PLACE THE TORQUE

WASHER/CARRIAGE BOLT ASSEMBLY INTO THE CORNER POST HOLES SO THAT THE HEAD OF THE CARRIAGE

BOLT FACES WHAT WILL BE THE INSIDE OF THE FORT. USE A HAMMER TO SET THE TORQUE WASHER INTO THE CORNER

POST.

8: ATTACH THE SWING BEAM MOUNT AS SHOWN IN DETAIL B.

THE THREE COUNTERSUNK

HOLES ON THE

SWING BEAM MOUNT

WILL FACE DOWN WHEN

PROPERLY INSTALLED.

BOLT

DETAIL B

3/8" WASHER

TORQUE WASHER

3/8" NUT

6-1/2" CARRIAGE

BOLT CAP

5/16 X 4-1/2"

(OFFSET HOLES DOWN)

SANDBOX BOARD

HEX BOLT

2 X 6 X 47-1/2"

WASHER

5/16"

2 X 6 X 47-1/2"

BOTTOM PANEL BOARD

(OFFSET HOLES DOWN)

4 X 4 X 47-1/2"

SWING BEAM MOUNT

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands