Gorilla Playsets Savannah II 1500FT Manual Download Page 78

Page: 78 / 123

(LEG ON INSIDE)

LEFT SIDE ASSEMBLY

#8 X 3"

WOOD SCREW

RIGHT SIDE ASSEMBLY

(LEG ON INSIDE)

NOTE: RAMP AND ROCK WALL

REMOVED FOR CLARITY.

26-3/8"

STEP 34: PICNIC TABLE

1: MEASURE 26-3/8" FROM THE BOTTOM OF THE CORNER POSTS ON THE LEFT SIDE OF THE PLAYSET. MAKE

MARKS ON THE INSIDE OF THE CORNER POSTS WITH A PEN OR PENCIL AT 26-3/8".

2: PLACE THE TOP OF THE RIGHT SIDE ASSEMBLY FLUSH TO THE MARK ON THE LEFT REAR CORNER POST.

ATTACH THE RIGHT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

3: PLACE THE TOP OF THE LEFT SIDE ASSEMBLY FLUSH TO THE MARK ON THE LEFT FRONT CORNER POST.

ATTACH THE LEFT SIDE ASSEMBLY TO THE INSIDE OF THE CORNER POST WITH #8 X 3" WOOD SCREWS.

Summary of Contents for Savannah II 1500FT




























































































































Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands

Gorilla Playsets Savannah II 1500FT, Manual

Search results

Summary of Contents for Savannah II 1500FT

Reviews:

Related manuals for Savannah II 1500FT

Brands by name

Popular brands