Gilera SMT RCR 633793 Service Station Manual Download

Page: 85 / 118

- If the throttle valve is replaced, fit another one

with the standard settings indicated on the upper

part as shown in the photograph

- Refit the complete the carburettor

- Refit the carburettor to the engine, connect the

fuel pipes again, the mixer oil intake pipes and the

low-pressure pipe for the fuel cock control

Adjusting the idle

- Tighten the flow set screw slowly until it stops and

then unscrew it as many turns as specified for this

type of engine (1+1/4)

- Remember this is the first adjustment

- Warm the engine up to the regular operating tem-

perature

- Adjust the idle speed at 1600 ± 200 rpm by op-

erating on the idle speed set screw (2)

- Turn the flow set screw (1) to both directions until

the maximum rpm possible is obtained

SMT RCR

Engine

ENG - 85

Summary of Contents for SMT RCR 633793























































































































Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands

Gilera SMT RCR 633793, Service Station Manual

Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands