Gilera SMT RCR 633793 Service Station Manual Download

Page: 78 / 118

Removal

Oil pump removal

- Remove the oil pump cover located on the engine

crankcase

- Remove the oil feed and delivery hoses from the

pump by operating on the flexible clamps

- Be careful to close the oil feed hose connected

to the pump so that the oil reservoir does not get

empty

- Remove the pump opening control cable by op-

erating first on the set screw retainer indicated in

the photograph and then on the pump cam retainer

- Remove the two screws fixing the pump to the

crankcase

- Remove the pump

- Make sure the pump drive rotates freely

- Make sure the sealing rings are in good condi-

tions. Replace them if they are damaged or dis-

torted

- The oil pump is a safety element for proper en-

gine operation. Replace it in case of faults; do not

repair it

Engine

SMT RCR

ENG - 78

Summary of Contents for SMT RCR 633793























































































































Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands

Gilera SMT RCR 633793, Service Station Manual

Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands