Gilera SMT RCR 633793 Service Station Manual Download

Page: 24 / 118

Air filter

- To reach the filtering element, remove the saddle

and the right side fairing.

- Afterwards, remove the 4 screws on the air filter

cover shown in the photograph.

Cleaning

- Wash the sponge with water and mild soap.

- Dry it with a clean cloth and short blasts of com-

pressed air.

- Soak the sponge in a solution of 50% petrol and

50% SELENIA AIR FILTER OIL.

- Gently squeeze the filtering element with your

hands without wringing it; let it drip dry and then

refit.

CAUTION

NEVER RUN THE ENGINE WITHOUT THE AIR FILTER,
THIS WOULD RESULT IN AN EXCESSIVE WEAR OF THE
PISTON AND CYLINDER.

transmissions

Transmission adjustment

- Adjust the control cables:

- Mix cable: see "Mixer timing" section.

- Throttle cable: adjust it in such a way that the sheath does not have any clearance.

- Splitter control cable: Adjust it in such a way that there is no clearance on the throttle grip.

- Adjust all transmissions in such a way that their sheaths do not have any clearance.

Mixer Timing

Maintenance

SMT RCR

MAIN - 24

Summary of Contents for SMT RCR 633793























































































































Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands

Gilera SMT RCR 633793, Service Station Manual

Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands