manualshive.com logo in svg

Gilera SMT RCR 633793, Service Station Manual

Share
Download
Gilera SMT RCR 633793 Service Station Manual Download Page 77

- Fit the hub (1) without interfering with the main

transmission gear. The hub should be aligned with

the main transmission gear (2), and then, after

manually turning the intermediate gear of the kick

starter (4), it should be aligned with the clutch hub

gear

- Fit the clutch hub washer

- Fit the hub, the star washer, the locking washer

and the fixing nut

- Lock the hub using the specific tool and tighten

the locking nut using the appropriate M17 wrench

- Fold the locking washer to secure the nut

- Lubricate the clutch plates with new oil

- Fit the transmission discs with the visible circle

on one of the clutch surfaces facing out

- Fit the clutch internal cover with the Gilera logo

in line with the visible notch on one of the clutch

hub teeth

- Fit the clutch springs and their fixing screws

Lubrication

Oil pump

SMT RCR

Engine

ENG - 77

Summary of Contents for SMT RCR 633793























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands