manualshive.com logo in svg

Gilera SMT RCR 633793, Service Station Manual

Share
Download
Gilera SMT RCR 633793 Service Station Manual Download Page 58

Cylinder assy. and timing system

Removing the cylinder head

Head fitting

- To refit it, carry out the removal operations but in reverse order

- Fit a new gasket between the head and the cylinder

- Make sure the coupling surfaces are perfectly clean

- Place the head on the cylinder and tighten the four stud bolts in two or three stages, tightening one

stud bolt and afterwards the one that is diametrically opposite

- Refit the thermoswitch and fit an adhesive gasket on the thread

- Fit the thermostat and its fixing nut

- Connect the thermoswitch connector and the spark plug tube - Connect the radiator coupling to the

cylinder head

- Connect the coupling from the radiator to the hydraulic pump

- Fill the cooling system reservoir with coolant

- Purge the system by operating on the coolant pump cap

Locking torques (N*m)

Stud bolts:

 

19 Nm

 

Screws

 

6 Nm

 

Thermoswitch

 

10 Nm

- Remove the coolant hose connecting the cylinder

to the water pump

- Use a container to collect the coolant

- Remove the hose from the head to the radiator

- Disconnect the temperature sensor electrical

connector.

- Remove the two M6 screws first and then the four

M7 stud bolts fixing nuts

- Remove the head and its gasket

- Remove any carbon deposits present on the

head being careful not to scratch the coupling sur-

faces

- Use a trued bar to check whether the head cou-

pling surface is flat. Maximum run-out allowed:

0.05 mm

Engine

SMT RCR

ENG - 58

Summary of Contents for SMT RCR 633793























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands