Gilera SMT RCR 633793 Service Station Manual Download Page 90

Page: 90 / 118

- Prepare a support with two gauging blocks in X.

- Position the stem as shown in the photograph

and use a dial gauge check alignment.

Serviceability limit: 0.2 mm

- Check the fork spring length.

- Make sure the spring does not show any signs of

abnormal wear or distortions. Replace it if it does.

- Check if the return spring and the guide nylon ring

are in good conditions. Replace them if damaged

or distorted.

- Thoroughly clean all the components.

Refitting

Carry out removal operations in reverse order being careful to observe the following tightening torques:

REFITTING

Name

Torque in Nm

Fork stem cap

17 ÷ 19 Nm

Fork plate upper clamp

8 ÷ 10 Nm

Suspensions

SMT RCR

SUSP - 90

Summary of Contents for SMT RCR 633793























































































































Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands

Gilera SMT RCR 633793, Service Station Manual

Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands