Gilera SMT RCR 633793 Service Station Manual Download Page 57

Page: 57 / 118

- Undo the three fixing screws and remove the sta-

tor from the crankcase

Refitting the flywheel magneto

- Align the symbol (1) on the stator with the centre

of the arrow (2) on the crankcase and fix it with 3

screws

- Connect the stator cables with the high voltage

coil and fix them to the chassis with the brackets

- Make sure the cable support inside the crankcase

is correctly positioned so that the cables do not get

into contact with the flywheel rotor

- Fit the flywheel rotor making sure that the wrench

is aligned with its guide

- Lock the flywheel using the specific calliper span-

ner and tighten the flywheel fixing nut

- Fit the other parts following the removal steps but

in reverse order

Specific tooling

020565Y

Flywheel lock calliper spanner

Locking torques (N*m)

Flywheel

35 ÷ 45 Nm

SMT RCR

Engine

ENG - 57

Summary of Contents for SMT RCR 633793























































































































Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands

Gilera SMT RCR 633793, Service Station Manual

Search results

Summary of Contents for SMT RCR 633793

Reviews:

Related manuals for SMT RCR 633793

Brands by name

Popular brands