Gigamon GigaVUE H TA100-CXP Hardware Installation Manual Download | Manualshive

Page: 90 / 115

background image

• Following are the nomenclatures for the GigaVUE TA Series node port numbers:

• Port numbers starting with a c (for example, c1) are 100Gb.
• Port numbers starting with a q (for example, q1) are 40Gb.
• Port numbers starting with an x (for example, x10) are 10Gb or 1Gb depending

on the transceiver installed.

N

OTE

: The 40Gb QSFP+ SR BiDi Full Duplex (RX/TX) transceiver is not supported in

conjunction with a BiDi TAP.

• For details about the supported transceivers, cable types, and connectivity

specifications, refer to

“GigaVUE-OS Compatibility and Interoperability Matrix”.

BiDi Optics Considerations

There are several nuances to consider due to the complexity in 40Gb BiDi technology.

Because of the nature of 40Gb BiDi technology, the same BiDi optic (Full Duplex or RX-
only) cannot be used in all of the following situations. For example:

• On SPAN sessions, RX-only BiDi optics cannot be used. Full Duplex BiDi optics must

be used.

• When receiving traffic from network links, RX-only BiDi optics must be used due to

the way traffic is multiplexed over the fiber pair in 40Gb BiDi technology.

• When deploying over inline 40Gb BiDi links, Full Duplex BiDi optics must be used.

• When connecting two GigaVUE TA Series nodes through a cascade connection, Full

Duplex BiDi optics must be used for the tool port. The network port may be either
Full Duplex or RX-only BiDi optics.

• When stacking multiple GigaVUE TA Series nodes, 40Gb BiDi optics must not be

used on stack links because the 40Gb BiDi technology is not compatible with the
Gigamon stack protocol.

Transceiver Installation Instructions

Gigamon transceivers are keyed and can only be installed in one direction. Transceivers
are hot-swappable – they can be installed or removed with the power on or off. Use the
following procedures to install and remove SFPs from GigaVUE TA Series node.

I

MPORTANT

: Always use an ESD-preventive wrist or ankle strap and ensure that it makes

good skin contact when installing or removing transceivers.

Installing Transceivers

1. Remove the dust cap from the port if present.

Contents

90

GigaVUE TA Series Hardware Installation Guide

«
...
88
89
90
91
92
...
»

Summary of Contents for GigaVUE H TA100-CXP




















































































































Reviews:

No comments

Related manuals for GigaVUE H TA100-CXP

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: Cambium Networks Pages: 68

Brand: Cambium Networks Pages: 110

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Brand: Lanner Pages: 109

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Brand: Watchguard Pages: 30

Brand: EMCIS Pages: 14

AXP-100H MUSCLE

Brand: Thermalright Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands