GEA EL44 Page 35 Instruction Manual And Installation Instructions Download

Page: 35 / 148

Technical data

Lubricant specifications

2018-9015-003
03-2015

35 / 148

4.6

Bolt torque chart

Note!

Refer to the bolt torque chart below unless otherwise specified in the manual.

Bolt

Mat.

Bolt diameter

1/4”

5/16”

3/8”

7/16”

1/2”

9/16”

5/8”

3/4”

7/8”

1”

SAE 2

LCS

8NM

6 ft-lbs

16NM

12ft-lbs

27NM

20ft-lbs

44NM

32ft-lbs

64NM

47ft-lbs

94NM

69ft-lbs

130NM
96ft-lbs

210NM

155ft-lbs

279NM

206ft-lbs

420NM

310ft-lbs

SAE 5

MCS

14NM

10ft-lbs

26NM

19ft-lbs

45NM

33ft-lbs

73NM

54ft-lbs

106NM
78ft-lbs

155NM

114ft-lbs

209NM

154ft-lbs

349NM

257ft-lbs

518NM

382ft-lbs

796NM

587ft-lbs

SAE 8

MCAS

19NM

14ft-lbs

39NM

29ft-lbs

64NM

47ft-lbs

106NM
78ft-lbs

161NM

119ft-lbs

229NM

169ft-lbs

312NM

230ft-lbs

515NM

380ft-lbs

814NM

600ft-lbs

949NM

700ft-lbs

Socket

Head

Cap

Screw

AS
HT

22NM

16ft-lbs

45NM

33ft-lbs

73NM

54ft-lbs

114NM
84ft-lbs

170NM

125ft-lbs

244NM

180ft-lbs

339NM

250ft-lbs

542NM

400ft-lbs

868NM

640ft-lbs

1315NM
970ft-lbs

4.7

Lubricant specifications

Lubricant type

Grades / Specifications

Purpose

All-purpose grease

Use this grade (or equivalent):

● EP2 mineral grease

● To lubricate the equipment.
● To grease the power steering

mechanism.

● To lubricate the slack adjuster.

Gearbox oil

● 80W90

● To fill the bearing housing.

Synthetic grease for

bearing intensive use

Use this brand (or equivalent):

● Texas 880 crown and chassis grease

● To grease wheel hub bearings.

AntiSeize high

temperature extreme

pressure lubricant

containing graphite

Use this brand (or equivalent):

● Wurth Sig 3000 grease

● To grease the coupling hand.

Hydraulic oil

Use these brands (or equivalent):

● Petro-Canada MV22

● Shell Tellus 32

● Exxon Nuto H32

● Mobil AW Hydraulic Oil 32

● To fill suspension cylinders bottom

translucent hose.

Biodegradable oil

Use this brand (or equivalent):

● PPG Chemfil Chemlube Agri-eco

1000

● To lubricate the primer pump piston.
● To spray over the spreader before

storing.

Summary of Contents for EL44





















































































































































Search results

Summary of Contents for EL44

Reviews:

Related manuals for EL44

Brands by name

Popular brands

GEA EL44, Instruction Manual And Installation Instructions

Search results

Summary of Contents for EL44

Reviews:

Related manuals for EL44

Brands by name

Popular brands