GEA EL44 Page 43 Instruction Manual And Installation Instructions Download

Page: 43 / 148

Assembly

Wheel and brake parts installation

2018-9015-003
03-2015

43 / 148

Red Loctite 242

To secure the hydraulic cylinder
bolts

AntiSeize high temperature
extreme pressure lubricant
containing graphite (Wurth Sig
3000)

To lubricate the ball hitch block and
the coupling hand

Items purchased locally

Provided by the owner:

● A PTO driveline meeting local requirements. Applicable only when this item

is not supplied by the manufacturer.

● A tractor of an appropriate tractor size.

6.4

Information on disposing of the packing material

Handle the packing material properly and dispose according to your valid local
regulations and rules on waste disposal. Please refer to your local resources for
any questions.

6.5

Wheel and brake parts installation

6.5.1

Preparing the spreader

Warning!

Do not stand under suspended loads. Falling loads can cause fatal
injuries!

Warning!

Wear protective boots, eye gear and gloves for all steps included in this
section.

Note!

If the spreader is assembled inside a building, make sure the doorway
is large enough to accommodate the spreader once assembled.

Note!

Park the spreader on a level and firm surface.

Note!

The hub, wheel and brake units are removed for shipping.

Summary of Contents for EL44





















































































































































Search results

Summary of Contents for EL44

Reviews:

Related manuals for EL44

Brands by name

Popular brands

GEA EL44, Instruction Manual And Installation Instructions

Search results

Summary of Contents for EL44

Reviews:

Related manuals for EL44

Brands by name

Popular brands