manualshive.com logo in svg

GE Corometrics 250cx Series, Service Manual, Page: 235 / 252

Share
Download
GE Corometrics 250cx Series Service Manual Download Page 235

Revision C

250cx Series Maternal/Fetal Monitor

A-11

2036947-001

Technical Specifications Strip Chart Recorder

Strip Chart Recorder

NOTE: 

Specifications are subject to change without notice.

Table 3. Strip Chart Recorder Technical Specifications

Heart Rate Scale
Chart Width:
Scaling:
Range:
Resolution:

Domestic

International

7 cm

8 cm

30 bpm/cm

20 bpm/cm

30–240 bpm

50–210 bpm

1 bpm

1 bpm

Uterine Activity Scale
Chart Width:
Scaling:
Range:
Resolution:

Strain Gauge

Tocotransducer

4 cm

4 cm

25 mmHg (3.3 kPa)/cm

25 mmHg (3.3 kPa)/cm 

0–100 mmHg (0–13.3 kPa)0–100 mmHg (0–13.3 kPa) 
1 mmHg/kPa

1 mmHg/kPa

Maternal Pulse Oximetry MSpO

2

 Scale

Chart Width:
Scaling:
Range:
Resolution:

Domestic

International

4 cm

4 cm

12.5%/cm or 25%/cm

12.5%/cm or 25%/cm

60–100% or 0–100%

50–100% or 0–100%

1%

1%

Recorder Drive
Speeds:
Speed Accuracy:

1, 2, and 3 cm/min
± 1%

Summary of Contents for Corometrics 250cx Series





























































































































































































































































Reviews:

No comments