GE Corometrics 250cx Series Service Manual Download Page 210

Page: 210 / 252

6-18

250cx Series Maternal/Fetal Monitor

Revision C

2036947-001

Parts List, Drawings, and Replacement: Assembly/Disassembly of FRUs

82. Connect orange connector receptacle of new power switch cable to orange

chassis-mounted plug.

83. Pull red tubes through chassis grommet towards Front-bezel.

84. Connect red tubes to Front-bezel NIBP connector.

85. Connect IUP cable to Front-end Motherboard.

86. Connect FECG cable to Front-end Motherboard.

87. Place FECG ground cable onto chassis post and tighten with nut.

88. Insert MECG and FECG cable beads into chassis bead clips.

89. Insert MSpO

cable beads into chassis bead clips.

90. Connect MECG cable to MECG board connector.

91. Connect MSpO

cable to SpO

Carrier board connector.

92. Connect Ultrasound cables to Ultrasound board connectors. The left- most

Ultrasound connector US1 cable goes to the rear connector on Ultrasound
board, J5.

93. Replace card cage cover. Re-insert screws.

94. Tilt the front bezel back onto chassis. Refasten screws to each side of chassis.

95. Connect 10-conductor DSP-to-UI Keypad ribbon cable to DSP board connector

J5.

96. Connect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

97. Connect 8-conductor Inverter cable to DSP board connector J1.

98. Place DSP board onto Main board. Use two screws to fasten DSP board to

chassis.

99. Connect external display cable from J9 on the DSP/Display PWA.

2025177-016 COMM Board

1. Remove top cover. Keep screws aside.

Remove four screws fastening the Comm. Board to the chassis.

Remove Comm. board from Main board.

Place new Comm. board onto Main board.

Fasten Comm. board onto chassis with four screws.

Replace top cover. Re-insert screws.

2025177-017 Recorder Assembly

1. Remove top cover. Keep screws aside.

Remove two screws fastening DSP board to chassis.

Remove DSP board from Main board.

Summary of Contents for Corometrics 250cx Series



























































































































































































































































Search results

Summary of Contents for Corometrics 250cx Series

Reviews:

GE Corometrics 250cx Series, Service Manual, Page: 210 / 252

Search results

Summary of Contents for Corometrics 250cx Series

Reviews: