GE Corometrics 250cx Series Service Manual Download Page 109

Page: 109 / 252

Revision C

250cx Series Maternal/Fetal Monitor

4-29

2036947-001

Maintenance: Ultrasound Transducer Test

Fetal Movement Detection

Ultrasound Transducer Test

Inspect an ultrasound transducer as follows:

Ensure there are no cracks around the transducer face.

Visibly inspect the condition of the cable, strain relief, and connector pins.

Disconnect the simulator’s ultrasound cable from the front panel of the 250cx
Series Monitor.

Connect the ultrasound transducer to either the

US2

input connector on

the front panel of the monitor. Verify the following on the monitor:

The FHR1 value shows three steady dashes “– – –.”

The FHR1 mode is

Table 5. Fetal Movement Detection Test Simulator Settings

Section

Switch

Setting

Ultrasound/FMD

Mode

US/FMD

Signal Level

MED

Rate

MANUAL

Main

CMR

Mode

TOCO

Summary of Contents for Corometrics 250cx Series



























































































































































































































































Search results

Summary of Contents for Corometrics 250cx Series

Reviews:

GE Corometrics 250cx Series, Service Manual, Page: 109 / 252

Search results

Summary of Contents for Corometrics 250cx Series

Reviews: