manualshive.com logo in svg

GE Corometrics 250cx Series, Service Manual, Page: 205 / 252

Share
Download
GE Corometrics 250cx Series Service Manual Download Page 205

Revision C

250cx Series Maternal/Fetal Monitor

6-13

2036947-001

Parts List, Drawings, and Replacement: Assembly/Disassembly of FRUs

15. Place top cover. Re-insert screws.

2025177-011 SpO

2

 Carrier Board with Masimo MSpO

2

 Module

1. Remove top cover. Keep screws aside.

2.

Remove two screws fastening DSP board to chassis. 

3.

Remove DSP board from Main board.

4.

Disconnect 8-conductor Inverter cable from DSP board connector J1.

5.

Disconnect 20-conductor DSP-to-LCD Decoder ribbon cable from DSP board 
connector J2.

6.

Remove card cage cover. Keep screws aside.

7.

Disconnect MSpO

2

 cable from SpO

2

 Carrier board connector. 

8.

Remove SpO

2

 Carrier board with Masimo MSpO

2

 Module assembly from 

Front-end Motherboard. 

9.

Insert new SpO

2

 Carrier board with Masimo MSpO

2

 Module assembly into 

Front-End Motherboard.

10. Reconnect MSpO

2

 cable to SpO

2

 Carrier board connector J10. 

11. Replace card cage cover. Re-insert screws. 

12. Reconnect 8-conductor Inverter cable to DSP board connector J1.

13. Reconnect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board 

connector J2.

14. Place DSP board onto Main board. Use two screws to fasten DSP board to 

chassis.

15. Place top cover. Re-insert screws.

2025177-012 SpO

2

 Carrier Board with TruSignal MSpO

2

 Module

1. Remove top cover. Keep screws aside.

2.

Remove two screws fastening DSP board to chassis. 

3.

Remove DSP board from Main board.

4.

Disconnect 8-conductor Inverter cable from DSP board connector J1.

5.

Disconnect 20-conductor DSP-to-LCD Decoder ribbon cable from DSP board 
connector J2.

6.

Remove card cage cover. Keep screws aside.

7.

Disconnect MSpO

2

 cable from SpO

2

 Carrier board connector. 

8.

Remove SpO

2

 Carrier board with TruSignal MSpO

2

 Module assembly from 

Front-end Motherboard. 

9.

Insert new SpO

2

 Carrier board with TruSignal MSpO

2

 Module assembly into 

Front-End Motherboard.

Summary of Contents for Corometrics 250cx Series





























































































































































































































































Reviews:

No comments