GE Corometrics 250cx Series Service Manual Download Page 206

Page: 206 / 252

6-14

250cx Series Maternal/Fetal Monitor

Revision C

2036947-001

Parts List, Drawings, and Replacement: Assembly/Disassembly of FRUs

10. Reconnect MSpO

cable to SpO

Carrier board connector J10.

11. Replace card cage cover. Re-insert screws.

12. Reconnect 8-conductor Inverter cable to DSP board connector J1.

13. Reconnect 20-conductor DSP-to-LCD Decoder ribbon cable to DSP board

connector J2.

14. Place DSP board onto Main board. Use two screws to fasten DSP board to

chassis.

15. Place top cover. Re-insert screws.

2025177-013 Front-end Motherboard

1. Remove top cover. Keep screws aside.

Remove two screws fastening DSP board to chassis.

Remove DSP board from board.

Disconnect 8-conductor Inverter cable from DSP board connector J1.

Disconnect 20-conductor DSP-to-LCD Decoder ribbon cable from DSP board
connector J2.

Remove card cage cover. Keep screws aside.

Disconnect Ultrasound cables from Ultrasound board connectors.

Remove Ultrasound board from Front-end Motherboard.

Disconnect MSpO

cable from SpO

Carrier board connector.

10. Remove SpO

Carrier board assembly from Front-end Motherboard.

11. Disconnect MECG cable from MECG board connector.

12. Remove MECG/FECG board assembly from Front-end Motherboard.

13. Remove Isolated Power Supply board from Front-end Motherboard.

14. Remove three insulating metal sheets from Front-end Motherboard.

15. Remove five screws fastening the Front-end Motherboard to the chassis.

16. Remove two screws on both sides of monitor fastening the front bezel to the

chassis.

17. Tilt the front bezel forward, away from the chassis.

18. Remove MSpO

cable beads from chassis bead clips.

19. Remove MECG and FECG cable beads from chassis bead clips.

20. Remove FECG ground cable from chassis post by removing nut.

21. Disconnect FECG cable from Front-end Motherboard.

22. Disconnect IUP cable from Front-end Motherboard.

23. Remove Front-end Motherboard.

24. Slide new Front-end Motherboard under card cage onto chassis.

25. Fasten to chassis with five screws.

Summary of Contents for Corometrics 250cx Series



























































































































































































































































Search results

Summary of Contents for Corometrics 250cx Series

Reviews:

GE Corometrics 250cx Series, Service Manual, Page: 206 / 252

Search results

Summary of Contents for Corometrics 250cx Series

Reviews: