GE AKTA ready Operating Instructions Manual Download Page 227 | Manualshive

Page: 227 / 227

GE AKTA ready Operating Instructions Manual Download Page 227

GE and GE monogram are trademarks of General Electric Company.

BioProcess, Capto, MabSelect, MabSelect SuRe, ReadyToProcess, Sepharose,
UNICORN and ÄKTA are trademarks of General Electric Company or one of its
subsidiaries.

Microsoft and Windows are registered trademarks of Microsoft Corporation.

Pluronic is a trademark of BASF SE.

TRI-Clamp is a trademark of Alfa Laval Corporate AB.

Triton is a trademark of Union Carbide Chemicals and Plastic Company Inc.

Tween is a trademark of Uniqema Americas LLC.

Vaseline is a trademark of Unilever Group.

All other third party trademarks are the property of their respective owner.

Any use of UNICORN is subject to GE Healthcare Standard Software End-User
License Agreement for Life Sciences Software Products. A copy of this Standard
Software End-User License Agreement is available on request.

© 2009-2015 General Electric Company – All rights reserved.
First published Sep. 2009

All goods and services are sold subject to the terms and conditions of sale of
the company within GE Healthcare which supplies them. A copy of these terms
and conditions is available on request. Contact your local GE Healthcare repre-
sentative for the most current information.

Any use of UNICORN is subject to GE Healthcare Standard Software End-User
License Agreement for Life Sciences Software Products. A copy of this Standard
Software End-User License Agreement is available on request.

GE Healthcare Europe GmbH
Munzinger Strasse 5, D-79111 Freiburg, Germany

GE Healthcare UK Limited
Amersham Place, Little Chalfont, Buckinghamshire, HP7 9NA, UK

GE Healthcare Bio-Sciences Corp.
800 Centennial Avenue, P.O. Box 1327, Piscataway, NJ 08855-1327, USA

GE Healthcare Japan Corporation
Sanken Bldg. 3-25-1, Hyakunincho Shinjuku-ku, Tokyo 169-0073, Japan

For local office contact information, visit
www.gelifesciences.com/contact

GE Healthcare Bio-Sciences AB
Björkgatan 30
751 84 Uppsala
Sweden

www.gelifesciences.com/readytoprocess

28960345 AD 10/2015 a139

«
...
225
226
227

Summary of Contents for AKTA ready




































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands