GE AKTA ready Operating Instructions Manual Download Page 100

Page: 100 / 227

Gradient flow section types

Two different ÄKTA ready gradient flow sections are available:

•

ÄKTA ready gradient High Flow section, with pump tubing diameter 12 mm and
tubing diameter 9.5 mm.

•

ÄKTA ready gradient Low Flow section, with with pump tubing diameter 8 mm and
tubing diameter 6.4 mm.

Both flow kits use 25 mm TC connectors for connecting to inlet and outlet containers,
pump tubing, and column.

NOTICE

Only use ÄKTA ready flow sections, supplied by GE Healthcare.

Specifications for ÄKTA ready flow kits are found in

ÄKTA ready gradient section specifi-

cations, on page 204

. Ordering information is in

ÄKTA ready gradient flow section, on

page 210

Installation of gradient flow
section

If you have selected the ÄKTA ready gradient checkboxes in the component list (see

System setup, on page 82

) you can follow the wizard to install the ÄKTA ready gradient

flow section. You may also follow the instruction below.

More information about mounting the flow kits can be found in

Section 6.3 Mounting the

flow kit, on page 81

Action

Step

Take the ÄKTA ready pump tubing from
the ÄKTA ready flow kit package. For a de-
scription of the content of the ÄKTA ready
flow kit package refer to

Three parts, on

page 78

100

ÄKTA ready Operating Instructions 28960345 AD

7 ÄKTA ready gradient

7.2 ÄKTA ready gradient flow section

Summary of Contents for AKTA ready




































































































































































































































Search results

Summary of Contents for AKTA ready

Reviews:

Brands by name

Popular brands

GE AKTA ready, Operating Instructions Manual

Search results

Summary of Contents for AKTA ready

Reviews:

Brands by name

Popular brands