EN
EN
94
95
IMPORTANT -
Before installing the mixing tool, always ensure that the opening
on top of the mixing tool shaft is clean and dry. Otherwise, the drive shaft of the
mixing drive could get polluted and/or damaged.
NOTE
Always move the mixing arm to the upper position, for inserting or removing the
mixing tools.
1. Ensure that the appliance is unplugged. Then move the mixing arm into the
upper position (see: ‘Preparation’).
2.
Disassembling the mixing tool:
Holding the mixing arm with one hand, push
the installed mixing tool upwards until you can turn the mixing tool easily clock-
wise (to the right). Then pull the mixing tool down off the drive shaft (see: ‘After
Usage / Removing the Mixing Tools’).
3.
Assembling a mixing tool:
Align the groove on top of the mixing tool shaft with
the securing pin on the drive shaft of the mixing drive. Holding the mixing arm
with one hand, push the mixing tool upwards until you can turn the mixing tool
easily counter-clockwise (to the left). Ensure that the mixing tool is locked securely
and cannot fall out/down.
4. Lower the mixing arm to the operating position. For this, hold the mixing arm
tightly at the front and press the unlock button. Ensuring that your hand stays
away from the joint of the mixing arm, gently lower the mixer arm to the opera-
ting position. Slide the splash guard into position on top of the mixing bowl and
gently press the splash guard down for fixing it on the mixing bowl.
NOTE
You may turn the splash guard to almost every required position. There is no need
to remove the splash guard for adding further ingredients. Simply fill the ingredients
in via the feed opening. Too large pieces of food should be cut to smaller pieces
fitting easily into the feed opening (e.g. cooked potatoes for purée).
STARTING THE MIXING PROCESS
NOTE
Use the splash guard to avoid that clouds of powdery ingredients and splashes
escape during operation. Turn the feed opening to the desired position. Liquid
ingredients, powder, and small pieces can be filled in via the feed opening. Add
flour in portions to the mixing bowl and use a low speed setting (1-2) until the sin-
gle portions are mixed in, for minimizing the build-up of flour dust.
1. Prepare the machine for operation (see: ‘Preparation’ and ‘Using the Mixing
Function’). Ensure that the mixing arm is correctly locked in the horizontal opera-
ting position. Connect the machine to a suitable wall power outlet (see: ‘Impor-
tant Safeguards for Electrical Appliances’). A beep sounds an the speed display
and operating time display show dashes. The stand mixer is now in standby
mode and ready for use.
WARNING
– Do not hold your hands or any foreign objects (e.g. rubber
spatula) into the mixing bowl or on the mixing tool, while the machine is connected
to the power supply. Always switch off the machine (press the control dial), before
manually scraping down your food in the mixing bowl.
2. Press the control dial for approx. 2 seconds for switching on the machine. A
signal sounds, the bowl illumination goes on, and the display areas show the
defaults: speed “00” and operating time “20:00”.
NOTE
Start with low speed settings (1 or 2), until the ingredients are combined. This
will minimize splashing and avoid clouds of powdery ingredients (e.g. flour). The
machine supports you in this via the smart motor control. The motor does not start
with a jolt, but increases the speed slowly to the set value. Therefore, when selec-
ting the speed, always wait for some seconds, until the selected speed is reached.
IMPORTANT -
Do not leave the motor operate continuously for more than 10
minutes to avoid overheating. Make breaks of at least 5 minutes after each 10
minutes of operation.
3. When the required mixing time is known already, you may adjust the operating
time accordingly. Use the arrow keys at the left side of the operating time display
to enter the desired time. The machine stops operation automatically, when the
set operating time ran out (see: ‘Operating Time and Pause Function’).
4. Turn the control dial clockwise for starting operation. As soon as the motor starts,
the count-down of the operating time starts.
