EN
EN
78
79
IMPORTANT SAFEGUARDS FOR ELECTRICAL APPLIANCES
Place the machine near a suitable wall power socket, and connect the
machine directly to a protected mains power supply with protective con-
ductor (earth/ground) connected properly. Ensure that the voltage rating
of your mains power supply corresponds to the voltage requirements of
the machine (230 V, 50 Hz, AC, rated for at least 8 A). The installation
of a residual current operated circuit breaker (r.c.c.b.) with a maximum
rated residual operating current of 30 mA in the supplying electrical circuit
is strongly recommended. If in doubt, contact your electrician for further
information.
• In various foreign countries, the specifications for power supplies are
subject to incompatible norms. Therefore it is possible that power sup-
plies in foreign countries do not meat the requirements for safe ope-
ration of the machine. Thus, before operating the machine abroad,
ensure that safe operation is possible.
• Do not use any extension cord or multi socket outlet. For operation,
always unwind the power cord completely.
• Power cords may never be knotted, twisted, pulled, strained or squee-
zed. The pins of the power plug must be neat and clean without any
discolouration. The insulation of the power cord may not be brittle or
worn. Do not let the plug or power cord hang over the edge of the
table or counter. Ensure that no one will pull the machine by the power
cord, or entangle in the power cord. Always grasp the plug to discon-
nect the power cord.
Do not touch the power plug or machine with
wet hands while the machine is connected to the power supply.
• The power cord may not touch hot surfaces, moving parts, or sharp edges.
Do not place the machine on a power cord. If the power cord is obviously
damaged and/or gets hot during operation, contact an authorized service
centre for replacement. DO NOT attempt to repair any power cord!
• Do not leave the machine unattended, while it is connected to the
power supply. Always switch off the motor (press the control dial) and
unplug the machine after operation and if the machine is not in use,
and before cleaning and/or assembling or disassembling.
• Leave hot food cool down before processing, because steam and
condensate escaping from hot food could damage the machine.
Always immediately wipe off any liquids and condensate from the
machine. To avoid risk of electric shock: Do not spill or drip any
liquids on the machine or power cord. Do not place or immerse the
machine or the power cord in water or any other liquid. Do not ope-
rate or even touch the machine, when it is wet or damp and con-
nected to the power supply. When the machine got wet, always
immediately unplug the machine and wipe dry to avoid risk of fire
and electric shock (see: ‘Care and Cleaning’). If in doubt, return the
machine to an authorised service centre for examination and repair.
•
Do not process very runny or liquid ingredients
via the mincer (e.g.
fresh fruit or light batter). Otherwise, liquid may get into the mincer
coupling at the mixing arm and cause risk of electric shock.
MOVING PARTS – RISK OF INJURIES
• While the machine is live: To reduce the risk of severe injury to persons
and damage, always keep your hands and any foreign objects (e.g. hair,
clothes, brushes, cooking utensils) out of the bowl and feed chute of the
mincer and away from the assembled tools (wire whisk, scraper beater,
or kneading tools). Always switch off (press the control dial) and
unplug
the machine, before assembling/disassembling any parts, cleaning, or
moving the machine and when not in use
. Do not grasp into the mincer
coupling when the machine is connected to the power supply.
• The edges of the cross blade are very sharp. Handle with care.
• Do not hold your face over the feed chute of the mincer, while the
motor is in operation. Residues of bones or other hard parts could be
hurled out. Do not poke in the feed chute! Do not push food into the
feed chute via your hands or any foreign objects. Only use the pusher
for pressing down food into the feed chute.
• Do not operate the machine without the mixing bowl in place—even
when using the mincer. Place the splash guard on the mixing bowl
whenever possible.
•
Do not leave the machine unattended when it is operation and/or
in reach of young children.
