manualshive.com logo in svg

GARDTEC 872, Installation Instructions Manual

Share
Download
GARDTEC 872 Installation Instructions Manual Download Page 58

E/E

Will activate for the duration of the entry exit times

Bell

Will activate when the bell is triggered and will cut of with the bell time

Alert

Will activate when an alert zone is triggered

Any Fire

Will activate when a fire zone is triggered

Any Panic

Will activate when a panic zone is triggered will also activate when a duress code is
entered

Alarm

Will activate when panel is in alarm and will reset when a code is entered 

Alarm B

Will activate when a second zone has alarmed (The activation of this output is
dependent upon other system attributes) Please refer to DD243 Section .

Alm Abort

Will activate when the panel is in alarm and unset within the programmed abort time 

O/C Cleaner

Used for sending open and closing when a cleaner code is used 

Cleaner Set

Will active when a cleaner code is used to set the system 

Gen Tamper

Will activate with bell / control / keypad / zex tampers

Zone 24Hr

Will activate when a 24Hr zone is triggered

Part Set

Will activate when the system is part set or when a zone is removed (omitted)

Strobe

Will activate when the strobe is triggered

Page 

57

GardTec 

872

Areas, Zones & Output Types

872.qxd  05/11/2003  15:01  Page 57

Summary of Contents for 872

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands