manualshive.com logo in svg

GARDTEC 872, Installation Instructions Manual

Share
Download
GARDTEC 872 Installation Instructions Manual Download Page 55

Zone Type Terminology (Areas & Attributes)

When programming the zone types other zone attributes including area allocation may
be programmed within the same screen. Please refer to the breakdown of the Zone
programming screen below.

Zone Programming Screen

Zone Number

The Zone number currently being programmed.

Zone Type

The current Zone Type (refer to previous page for terminology.

Area(s)

Area(s) that the current zone is allocated to.

Zone Attribute

Attribute for current zone. Attributes available are:-

Remove-

Zone cannot removed (omitted) by the end user.

Rem+/Dk

Zone may be removed (omitted) by end user and is also Double 
Knock.

Page 

54

000=Ent/Ex                 A=
1

234567 

Rem -

Zone Number

Zone Type

Area(s) Zone is allocated to

Zone Attribute

GardTec 

872

Areas, Zones & Output Types

872.qxd  05/11/2003  15:01  Page 54

Summary of Contents for 872

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands