GARDTEC 872 Installation Instructions Manual Download Page 28

Page: 28 / 112

Page

Fig. 16 ProDigi or GardTec Modem Wiring.

Note:

Modem will give 8 channels and leave D1, D2 & D3 (PA term) free for
other uses

For a ProDigi program Digicom Type to Gardiner

For Modem Mod+FF or MOD+PID

Remove link from 12V & Line Fault Terminals before connecting
ProDigi/Modem

Both the ProDigi and GardTec Modem can be programmed direct from the
GardTec

872

control panel

Modem Patch Lead

If the GardTec Modem patch lead is to be used for direct connection to a PC or Lap-
Top It should be connected to SK3.

The factory fitted link between 12V & Line Fault

must be removed.

Full instructions on use of the GardTec Modem Patch lead are

supplied with the unit.

Gardtec 840
Main PCB

Communicator
SK3

ProDigi

Gardtec Modem

GardTec

872

Main PCB

If the GardTec Modem is used
basic system configuration is
available by defaulting the system
using

5, 5, YES, NO.

Further

details are given in the GardTec
Modem manual.

GardTec

872

Wiring Connections

Modem Patch Lead if
direct connection to PC
is required.

872.qxd 05/11/2003 15:01 Page 27

Summary of Contents for 872

















































































































Search results

Summary of Contents for 872

Reviews:

Brands by name

Popular brands

GARDTEC 872, Installation Instructions Manual

Search results

Summary of Contents for 872

Reviews:

Brands by name

Popular brands