manualshive.com logo in svg

GARDTEC 872, Installation Instructions Manual

Share
Download
GARDTEC 872 Installation Instructions Manual Download Page 32

Page 

31

Fig. 20 Traditional bell box wiring.

Fig. 21 Novagard wiring

The Gardtec 

872

may be used with the Novagard Active range of external

sounders.When used in Novagard Active mode additional programmable features and
diagnostics are available even from a remote location using the Gardtec Remote
Software package. Diagnostics help to identify failures or potential failures without the
need to send an engineer on a site visit.

STROBE 

+            -

BELL 

+           -

BELL 

HOLD-

SAB 

TMP

N/C Microswitch

Siren/Bell

Strobe Light

Gardtec 

800 Series

STROBE 

+         -

BELL 

+         -

BELL 

HOLD-

SAB 

TMP

Gardtec 

800 Series

+         - 

STROBE

+         - 

SUPPLY

F 

TAMP 
FEED

BELL 

SW-

R 

TAMP 

RET

Program panel 
for Bell Tamper 
Ring

NOVAGARD 
1E, 2+T, 2D, 
3, 3PD, 3PC, 3A, 3B, 
3C, 4, 4B, 4D, 4Q 
& Encapsulated SAB/Strobe

Note: 

Terminal positions may change dependent on model.

GardTec 

872

Wiring Connections

Typical Novagard

+        -      

BELL    SAB

  BELL         HOLD   TMP

STR    BELL    12V      0V    TMPR
SW-     SW-      IN        IN      RTN

Novagard Active

Wired & configured

as Unit No.1

Gardtec 590/591

Control Panel programmed

for 1 Novagard Active

3    2    1

JP1

For details of wiring multiple Novagard Active sounders 

please refer to Novagard Active Instructions

872.qxd  05/11/2003  15:01  Page 31

Summary of Contents for 872

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands