Fujitsu AOTG36LATT, Service Manual

Page: 93 / 264

En-8
Overlap the insulation
Vinyl tape
Wrap with cloth tape
Cloth tape
Drain hose
Pipe
Connection pipe
(heat insulation)
Indoor unit pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
Seal A is used when the diameter
of gas pipe is Ø12.70 or more.
Butt connection pipe (heat
insulation) against the indoor
unit pipe (heat insulation) and
wrap with seal A so that there
is no gap.
Connection cable
Pipe
Drain hose
Drain hose Connection pipe
Wall pipe Connection cable
Left piping
For connection from the left rear
Check the following:
GOOD
Drain hose
Saddle
Lifted up Wave End in water
PROHIBITED
9. FRONT PANEL REMOVAL AND INSTALLATION
Intake grill removal Intake grill installation
b
a
Open the intake
grille. While gently
pressing the left
and right mounting
shafts of the intake
grille outward “a”,
remove the intake
grille in direction of
the arrow “b”.
c
While holding the
grille horizontal, set
the left and right
mounting shafts into
the pillow blocks at
the top of the panel
“c”.
To latch each shaft
properly, insert the
shaft until it snaps.
Press 4 places on
the intake grille to
close it completely.
9.1. Front panel removal
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove 3 caps.
(3) Remove wire cover.
(4) Remove 7 screws.
Screws (Wire cover )
Screws ( 7 position )
Caps ( 3 position )
Wire cover
Diffuser
NOTE : When replacing the front panel, do not scratch or damage the diffuser.
(5) The front panel is pulled to the front, raising the upper surface, then the front panel is
removed.
Front panel
9.2. Front panel installation
(1) First, fit the lower part of the front panel, and insert top and bottom hooks. (3 top
sides, 2 center)
Indoor unit
Front panel
Top hooks
(3 position)
Top holes (3 position)
(2) Attach the 7 screws.
(3) Attach the wire cover.
(4) Attach the 3 caps.
(5) Attach the intake grille.
CAUTION
Install the front panel and intake grille securely. If installation is imperfect, the front
panel or intake grille may fall off and cause injury.
10. TEST RUN
Check items
(1) Is operation of each button on the remote control unit normal?
(2) Does each lamp light normally?
(3) Do air flow direction louvers operate normally?
(4) Is the drain normal?
(5) Do not have an abnormal noise and vibration during operation?
• Do not operate the air conditioner in test run for a long time.
[Operation method]
• For the operation method, refer to the operating manual.
• The outdoor unit, may not operate, depending on the room temperature. In this case,
keep on pressing the MANUAL AUTO button of the indoor unit for more than 10
seconds. The OPERATION indicator lamp and TIMER indicator lamp will begin to flash
simultaneously during cooling test run.
Then, heating test run will begin in about 3 minutes when HEAT is selected by the
remote controller operation [reverse cycle model only].
(Please follow the operating manual for remote controller operation.)
• T o end test operation, press the remote controller START/STOP button.
(When the air conditioner is running by pressing the test run button, the OPERATION
Lamp and TIMER Lamp will simultaneously flash slowly.)
[Using the wired remote controller] (Option)
For the operation method, refer to the operating manual.
(1) Stop the air conditioner operation.
(2) Press the MODE button and the FAN button simultaneously for 2 seconds or more to
start the test run.
Test run display
(3) Press the START/STOP button to stop the test run.
ASTG18KMCA_中型標準モデルLM系_R32_0724m.indd 8 2013/07/24 16:52:10