manualshive.com logo in svg

Fuji Xerox DocuPrint CP225 w, User Manual

Share
Download
Fuji Xerox DocuPrint CP225 w User Manual Download Page 43

Printer Connection and Software Installation

43

Printing and Checking the System Settings Page

Print the System Settings page and check your printer's IP address.

Using the Operator Panel

1

Print the System Settings page.

See also: 

•

"Printing a System Settings Page" on page 101

2

Confirm the IP address next to 

IP Address

 under 

Wired Network

 or 

Wireless Network

 on the System 

Settings page.
If the IP address is 

0.0.0.0

, wait for a few minutes to resolve the IP address automatically, and then print the 

System Settings page again.

If the IP address is not resolved automatically, see "Assigning an IP Address Manually" on page 40.

Using the Printer Setting Utility (Windows Only)

1

Print the System Settings page.

See also: 

•

"Printing a System Settings Page" on page 101

If the IP address is 

0.0.0.0

 (the factory default) or 

169.254.xx.xx

, an IP address has not been assigned. 

Summary of Contents for DocuPrint CP225 w




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands