Fuji Xerox DocuPrint CP225 w User Manual Download Page 156

Page: 156 / 187

156

Troubleshooting

Wi-Fi Direct Problems

Problem

Action

The device cannot discover the
printer.

The printer may be connected to another device via Wi-Fi Direct

. Disconnect the

printer and the device. For details, see "Disconnecting Wi-Fi Direct Network" on
page 97.

The printer cannot disconnect from
the device even when the procedure
in "Disconnecting Wi-Fi Direct
Network" has been performed.

The device may be automatically reconnecting to the printer. Reset the
passphrase for Wi-Fi Direct and disconnect the device. For details, see "Resetting
the Passphrase" on page 98.

The network mode of the printer
cannot be set to

Ad-Hoc

mode on

the CentreWare Internet Services.

Make sure that

Wi-Fi Direct

is set to

Disable

Wi-Fi Direct

cannot be set to

Enable

Make sure that the network mode is set to

Infrastructure

mode on the

CentreWare Internet Services.

Summary of Contents for DocuPrint CP225 w



























































































































































































Search results

Summary of Contents for DocuPrint CP225 w

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuPrint CP225 w, User Manual

Search results

Summary of Contents for DocuPrint CP225 w

Reviews:

Brands by name

Popular brands