manualshive.com logo in svg

Fuji Xerox DocuPrint CP225 w, User Manual

Share
Download
Fuji Xerox DocuPrint CP225 w User Manual Download Page 177

Maintenance

177

Conserving Supplies

You can change several settings in your print driver to conserve toner cartridge and paper.

Supply

Setting

Function

Toner cartridge

Windows print driver:

Toner Saving Mode

 in the 

Graphics

 tab

This feature allows the users to select a print mode that 
uses less toner.
When this feature is used, the image quality will be lower 
than when it is not used.

Print media

Windows print driver:

Multiple Up

 in 

Layout

 tab

The printer prints two or more pages on one side of a 
sheet. The available numbers that each print driver can 
print one sheet of paper are as follows:

•

Windows print driver: 2, 4, 8, or 16 pages 
Combined with the duplex setting, 

Multiple Up

 allows 

you to print up to 32 pages on one sheet of paper. (16 
images on the front and 16 on the back)

Summary of Contents for DocuPrint CP225 w




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands