manualshive.com logo in svg

Fuji Xerox DocuPrint CP225 w, User Manual

Share
Download
Fuji Xerox DocuPrint CP225 w User Manual Download Page 34

34

Printer Connection and Software Installation

Connecting Printer to Your Computer

USB Connection

To connect the printer to a computer via USB:

1

Make sure that the printer is turned off and unplugged from the power source.

2

Connect the smaller USB connector into the USB port at the rear of the printer and the other end to a USB port 
of the computer.

NOTE: 

•

Do not connect the printer USB cable to the USB slot available on the keyboard.

Ethernet Connection

To connect the printer to a computer via Ethernet:

1

Make sure that the printer is turned off and all cables have been disconnected.

2

Connect one end of the Ethernet cable into the Ethernet port at the rear of the printer and the other end to an 
Ethernet port of a router or hub.

NOTE: 

•

Connect the Ethernet cable, only if you need to setup a wired connection. Connecting the Ethernet cable stops some features 
or functions for Wireless network.

USB port

Ethernet port

Summary of Contents for DocuPrint CP225 w




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands