manualshive.com logo in svg

Fuji Xerox DocuPrint CP225 w, User Manual

Share
Download
Fuji Xerox DocuPrint CP225 w User Manual Download Page 166

166

Maintenance

Cleaning the Printer

This section describes how to clean the printer in order to maintain it in good condition and print clean printouts all 
the time.

Cleaning Inside the Printer

1

Turn off the printer and disconnect the power cord.

2

Open the toner access cover.

3

Pinch the toner cartridge firmly.

4

Pull the toner cartridge out.

IMPORTANT: 

•

Always pull the toner cartridge out slowly so you do not spill any toner. 

5

Pull the other three toner cartridges out as well.

WARNING:

•

When cleaning this product, use the designated cleaning materials exclusive to it. Other cleaning materials may 
result in poor performance of the product. Never use aerosol cleaners to avoid catching fire and explosion.

CAUTION:

•

When cleaning this product, always switch off and unplug it. Access to a live machine interior may cause electric 
shock.

Summary of Contents for DocuPrint CP225 w




























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands