Fröling GAR 110 Installation And Operating Instructions Manual Download Page 31 | Manualshive

Page: 31 / 48

background image

4.3.6 Fitting adjustable feet in boiler room (optional)

If the closed duct in the boiler room exceeds 2m, an additional support is
recommended:

Ø 15 mm

❒

Remove the brackets from the supporting post

❒

Remove the screws of the trough flange at the relevant position

❒

Secure the brackets to the trough flange with the previously removed screws

❒

Position the supporting post at the bracket and screw together

Screwing the adjustable feet to the floor:

❒

Make two holes each in the floor on the left and right for the adjustable feet

❒

Drill the holes marked
- Drill diameter 15 mm
- Min. drill depth 105 mm

❒

Insert the heavy load anchors into the bore holes and tighten with a spanner (AF
17 mm)

4.3.7 Closing the wall penetration

❒

Pack the space in the wall penetration with a non-flammable insulating material

➥

The partition must be insulated to conform with ÖNORM B 3836 or DIN
4102-11!

❒

Close the wall penetration on the store side and the boiler room side with a non-
flammable covering

NOTICE

Do not connect the transfer channel to the brickwork (with concrete), as this
will transfer sound through all the brickwork.

Assembly

4

Assembling the articulated arm rotary agitator

Installation and Operating Instructions GAR 110 / 150 | M2060120_en

31

«
...
29
30
31
32
33
...
»

Summary of Contents for GAR 110

















































Reviews:

No comments

Related manuals for GAR 110

Brand: NAD Pages: 10

Brand: Dairyland Pages: 21

Brand: UNIA Pages: 62

Brand: ACCU-CHECK Pages: 104

Brand: B-K lighting Pages: 3

Brand: Eagle Eye Pages: 21

Brand: Labomed Pages: 67

GPSMAP 188 Sounder

Brand: Garmin Pages: 134

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: Parker Pages: 52

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

Brand: Yamaha Pages: 45

Brand: GE Pages: 37

Brand: Marcy Pages: 9

Brand: Abus Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands