Fröling GAR 110 Installation And Operating Instructions Manual Download Page 9

Page: 9 / 48

2.3 Qualification of staff

2.3.1 Qualification of assembly staff

CAUTION

Assembly and installation by unqualified persons:

Risk of personal injury and damage to property

During assembly and installation:

❒

Observe the instructions and information in the manuals

❒

Only allow appropriately qualified personnel to work on the system

Assembly, installation, initial startup and servicing must always be carried out by
qualified personnel:

- Heating technician / building technician
- Electrical installation technician
- Froling customer services

The assembly staff must have read and understood the instructions in the
documentation.

2.3.2 Personal protective equipment for assembly staff

You must ensure that staff have the protective equipment specified by accident
prevention regulations.

▪ For transportation, setup and assembly:

- suitable work wear
- protective gloves
- sturdy shoes (min. protection class S1P)

2.3.3 Qualification of operating staff

CAUTION

If unauthorised persons enter the Storeroom:

Risk of personal injury and damage to property

❒

The operator is responsible for keeping unauthorised persons, in particular
children, away from the system.

Only trained operators are permitted to operate the unit. The operator must also have
read and understood the instructions in the documentation.

Safety

Qualification of staff

Installation and Operating Instructions GAR 110 / 150 | M2060120_en

Summary of Contents for GAR 110

















































Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands

Fröling GAR 110, Installation And Operating Instructions Manual

Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands